After building a number of dovetail puzzle boxes the HipMonsters sister team set out to make their own unique design. We explored many designs and drew influence from creations like this one on YouTube. The sisters wanted something that looked deceptively simple and easy to make. Thus was born Push My Button!
Please note, this material is provided for entertainment and informational purposes only and is not a guide on how to create the designs. Please read our disclaimer.
Side View
Here is Push My Button from side view. The sides of the box are made from a several of 1/4 wooden square dowels. These are our go-to material for many of our designs.
Top View
The top, sides and bottom are made from 1/8 inch plywood.
Corner view
Here is a view of a corner. We purposely made it look slapped together to confuse people. The lopsided look makes it appear that the sides of bottom can be slipped off – which cannot be done.
Which button to press?
But the key to opening Push My Button to to press the correct button… but which one? We added spacers between some of the dowels and aligned them irregularly to make harder to tell which one is the key.
Opened!
When we give it as a gift, we usually leave earrings or chocolate inside to reward the receiver once them uncover the trick.
We wanted to give people a scare on Halloween and was inspired by a visit to Rosicrucian Egyptian Museum so we set out to make our own mummy, George the mummy (he got too curious).
Please note, this material is provided for informational purposes only and is not a guide on how to create the designs. Please read our disclaimer.
Materials
For the mummy, we used:
A roll of burlap fabric
Lots of brown shipping paper
Chicken wire
Aluminum fense wire
5 1/4×1/4X 5 Wood
Twine
nuts and bolts.
We needed it to be pretty light so we didn’t use a lot of wood and padded the skeleton with lots of shipping paper. We had been storing the shipping paper for years and had bags of it in a closet for just such a project. It is perfect because it looks like old dried skin!
Cutting the joint
We wanted George to be flexible so we could place him through out the house and even take him on car trips.
Close-up of the joint
This is one of the joints that we made. George is fully articulate but not powered like our robots.
Trimming the sides
We cut small pieces of the wood off to make it more rounded then sanded the edges to get a clean joint. Since these joints would not be seen we used only rough grade sandpaper.
The finished joint
We drilled holes in the joints so that we could put them together. To drill the holes we clamped the two pieces together to assure the holes would align.
Putting them together
We used a rubber washer between the two pieces so George the Mummy would not be too wobbly. After screwing the bolts down we crimped end to make sure they would not come undone after George was finished.
Starting the head
We used chicken wire to start making the shape of the head. The chicken wire was so sharp so we had to be extra careful not to cut ourselves. Best to let a parent do this part. One trick we used was to warp the end pieces in duck tape to make them less pocky.
The basic shape of the head
We molded the head into shape. We recomend wearing thick gardening gloves because the chicken wire is very sharp.
Wrapping it in paper
We wrapped it in paper to make it less sharp and because the paper looks like dry skin. The paper alos helps makes the linbs more circlular.
George’s head with the skin
The head fully wrapped in paper.
Securing the paper
We secured the paper by tightly wrapping it in twine. we used twine because it is strong, but also because it is the same color as the paper, so if a little shows it would blend in with the paper.
Wrapping it in burlap
We wrapped it up in burlap after we finished securing the paper. We did several layers so it wouldn’t come off and towards the end split the burlap into multiple strips
The completed head
After the head was done it was on to the rest of the body. The wooden skeleton we made as simple ae possible and used bolts and bolts with crimp washers to make sure it would not come loose after the wrapping for completed.
Put it together!
Now assemble the skeleton and wrap the body in the same fashion as the head. Wrapping the hands and feet proved to be very hard, and we ended up not making wooden fingers, we just wrapped the arm and secured the ends.
Waiting to be wrapped
Here is the completed skeleton fully covered in paper and tied together with twine. We needed to remove the final wrapping from the head in order to better integrate it to the body. Also, we tried using left over hand from out Hand of Glory project but in the end, they did not look as real as we want.
The side viewFront view
Now you can see George out of the workshop! We originally tried to make him be able to stand up on his own, but that would mean either making the body weirdly small or making the feet gigantic. We ended up attaching him to a lamp post instead.
George the mummy exercising
In this photo, George is sitting on a stationary bicycle. This shows off how George’s limbs can move and that he can be detached from the lamppost. It also shows that George is about the same size as a normal human, which makes him more realistic and creepy.
George taking down holiday decorations with Number Three
In this video, George the Mummy is taking down Christmas decorations with Number Three, showing off how well he stands and how much he enjoys wearing hats. He is also sturdy enough to hold Christmas tree ornaments without his arm bending.
We decided to make a special present for our teachers at school. One of the teachers really loved alligators, so we decided to make one for her out of wood.
Please note, this material is provided for informational purposes only and is not a guide on how to create the designs. Please read our disclaimer.
So we set out to make one out of wood. First we cut the wood into the rough shape of the toy.
Next, We drilled the wood that we cut. We cut lots of little pieces so the tail could move. We also drilled a small hole in the center of each small piece.
To smooth the edges we used a wood plane. Then we sanded each piece with fine grain sandpaper. For the details on the head we made rough cuts using an alligator saw then sanded repeated to get the shape we wanted.
We laid out the final design before threading the wire through the holes we drilled.
Here we are threading the wire though the holes. We used pipe cleaners to get a snug fit. This will make the toy alligator flexible but will also hold its shape well.
The Hip Monsters team decided to make something that interests people when they walk into the room. Inspired by Girl Genius and this Steampunk creation, we made a mysterious steampunk contraption that only we know the use of.
Our amazing steampunk device.
This is our steampunk creation. It has two light bulbs, a pressure gauge, and some metal pipes. The light bulbs’ brightness is adjustable.
The side view
This is the side view of our device. You can see that on the side of the creation, there is a silver metal box. That controls the brightness of the lightbulbs.
The back view
On the back, you can see that there is a wire going from the silver box away from the device. that is where you plug in the device to the outlet. From the front it is barely noticeable, you can only see it from certain angles.
With all the potion-making we have been doing recently, we found that we needed a place to put our potion supplies on the go, so we made a potion cabinet fit for the experts of potion-making. Professor Slughorn’s portable potions kit was the main inspiration for this creation.
Please note, this material is provided for informational purposes only and is not a guide on how to create the designs. Please read our disclaimer.
Getting started
We used the following supplies; a hammer, a saw, four 90-degree angle clamps, black paint, blue paint, mahogany-colored wood stain,
Using clamps to get a tight fit
The core of the cabinet is the frames. These carry the weight of the bottles and hold the cabinet’s shape. To make the frames, we cut the beams into 12 inches and glued them together, using the 90-degree angle clamps for making a strong right angle.
Getting the pieces ready for assembling.
All the sides and frames are ready for assembly. All pieces need to be cut out before you start assembling to make sure that you don’t forget a piece.
Gluing the pieces together.
We ran a bead of glue on all the edges of the frames. We made sure to only put a little glue to prevent sliding.
Clamping the cabinet together.
Then we use clamps to firmly secure the sides to the frame.
Hammering in nails for support.
Once we were sure the glue had dried we went on to the next steps. For added strength, we put in a few thin nails on the bottom and sides.
Measuring the box for the shelf.
We measured for the interior shelf after we put the cabinet together to make sure we have a snug fit.
Cutting the corners of the shelf.
Next we cut out slots on all the corners so the shelf following the outside of the line then sanded to fit the cabinet.
Attaching the handle to the top.
Finally, we added a handle on top to make transportation easier. Since the outside plywood was thin to make the cabinet light, we added an extra piece of wood underneath to secure the handle. we used thin screws so we don’t split the extra piece of wood.
The fully assembled cabinet.
Here is the assembled cabinet ready for staining and painting. We are looking for a vintage look so we need to do multiple layers and light distressing.
We stained the cabinet and left it outside to dry. The shelf and front were stained separately to make sure that we got the stain in all the nooks and crannies.
Adding wax circles on the top of the cabinet.
We used candles to make wax circles around the cabinet. We do this because when we paint it, the paint on the wax would peel off, creating a distressed look.
Painting the cabinet.Sanding some of the paint off.
Then, we mixed the black paint and the blue paint, creating a dark blue, and painted the cabinet. We used dark blue because when black paint gets old, it looks like dark blue.
We lightly sanded the painted wood, showing the stain underneath. We can repeat this process to get the aged look that we desired. Here is a view of the completed potion cabinet with the vintage finish.
Photo with the cabinet door.
Here is a view with the case close for safe transportation!
The door closed.
Here is the completed potion cabinet with a vintage finish.
This project is about how to build a ladder bookcase. This bookcase has less room because its sides slope in towards the top but fit well into small spaces and is very sturdy, a perfect place for books! This design was inspired by a model designed by Vico Magistretti.
Please note, this material is provided for informational purposes only and is not a guide on how to create the designs. Please read our disclaimer.
All the Supplies Laid Out
First, you get all the materials:
2 clamps
a bottle of wood glue
5 48 X 3.5 X .5 inch wood planks (we used reclaimed wood)
4 36 X 5/8 inch Oak Dowel Rods
4 48X 2 X 3/4 inch cheery wooden boards
a saw
sandpaper (Course and fine grit)
drill
3/4 inch bit
4 MDF Wood Board 6x8x.0785
Wood Stapler
No Screws or nails!
Measuring carefully
Now you can begin. First, on the 48X 2 X 3/4 inch cherry beam make a straight line one inch from the top. This you will line up with the edge of the circular saw.
Cutting carefully
Next, you cut a twenty-degree angle so that the tip touches the corner.
Our Japanese saw in good use
Then, if there is access cut it off while not impacting the angle.
Measuring again
Then, you make dots 11 inches apart in the center of the 48X 2 X 3/4 inch cherry beams.
Clamping wood to align drilling
Next, you clamp both pieces of wood together, to make drilling more accurate.
Drilling carefully
Then, you drill a hole on all the dots while keeping the wood clamped together.
All the holes align!
Put them aside to use later.
Planning out the next steps
Then, mark 3 of the 48 by 3.5 by 0.5-inch wooden boards at 22 inches.
Measuring the support
Next, measure a 36 X 5/8 inch pole and mark it at fifteen inches.
Cutting the support poles
Then, cut the pole at your mark, repeat 9 times. if the pole is too wide for your hole, sand it, if it is too thin, then wedge some pieces of wood between the pole and the hole.
Almost assembled!
Next, stick the poles in the holes that you drilled so that it looks like this. After that, put the other two wood beams on the other side as well. Make sure not to alternate.
Measuring the shelves
Nearly done, mark the other three 48 X 3.5 X .5 inch boards at 30 inches each.
Clamping the shelves for cutting
Finally, clamp all three of the boards together. Then, cut them at 30 inches while keeping them clamped, and remember to use both sides for shelves.
Cutting the shelves
Clamp the shelves together while sawing to make it much easier.
Finished!
Now you have a amazing ladder bookcase! The finished shelves was quickly put into use for storing our large StarTrek fiction and RPG book collection.
Born from one of our favorite bushes and a failed costume, Lin the dragon was our most complex monster at that time. Lin is made from wood from our own garden, making her unique.
Flying free!
Lin has posable legs, tail and wings. The legs can barely support her so we decided to hang her from the ceiling to watch over us as we craft.
Side viewClose up of a wing joint
The wings are from a dragon costume we were building that proved to be too heavy. The tail is made by repeatedly cutting the log and threading a steal wire through them to secure it.
The hummingbird monster was made from a branch too weak to be used for other projects. We decided to make it into a hummingbird because it already had a long beak, and the body was already shaped like a bird. After lots of trimming, sanding, and bees wax, we added felt and wire wings.
Bottom view
Hung from the ceiling, the humming bird monster comes to life.
We call this monster the Anteater. The Anteater monster was a wonderful branch that was too split to make a good wand or use in other projects. After we stabilized the splitting and cut out all the rotted wood, we sanded her and coated her heavily in bees wax.
Side view
At first we thought of mounting Anteater on the wall as if she was a trophy, but then the Sister’s team thought of having her appear to climb out of the wall. We then used a picture frame we were working on and created a fake window using the picture frame, paint, and plexiglass for her to climb out of. With a window as a mount, she made a great addition to our living room.
The Hip Monster’s sister team has created a DIY pump drill. Pump drills are ancient tools used by many cultures including Native Americans. The sisters got the idea from seeing pump drills made by the Miwok tribe who used to live in California.
Please note, this material is provided for informational purposes only and is not a guide on how to create the designs. Please read our disclaimer.
Some of the supplies
Equipment:
saw
drill
spade drill bit ~1 inch
drill bit 1/8 inch
spokeshave
sandpaper
strong string
bee’s wax
three long, straight branches
Branches:
1) shaft: the centerpiece of the pump drill. Look for a long, straight, and thin piece of wood.
2) spindle whorl: Attached near the tip of the shaft and makes the drill rewind. This piece should be heavy and thick enough the shaft can go through it.
3) handle: What you hold onto. This piece should be just thick enough for the shaft to go through.
First, you pick out three straight pieces of wood, one long and skinny, and the other two thick. Make sure the handle and the spindle ones are thick enough for the shaft to go through. Cut off the extra parts making sure to leave a bit extra on each end.
This se should look like this. The extra inch on each side of the sticks are so you can secure them to a vice for shaving.
The first one will be the spindle, the second the handle, and the last the shaft.
Next, spokeshave the pieces to make them smooth. Be very careful while spoke shaving you don’t want to make any of the pieces too thin or curved. Continuously flip the piece over to get to make all the sides are even. Sometimes when there is a knot or we accidentally cut into the wood, an adult can help smooth it out. If you have finished spoke shaving but don’t have enough time to stain or wax it, soak it in water so it doesn’t dry out to much.
For the main shaft, spokeshave till it is as straight as possible. To find out which side to shave roll the stick on a table and see which part is bent up. For the handle and spindle, you just need to get the bark off.
Now cut the piece to the right size. Make sure the thin one is the longest because that would be the main piece that supports everything else. Measure everything out the right size before you cut it.
Sand the pieces to make them really smooth. Spend more effort on the shaft. Remember, the shaft needs to be smooth and straight for the pump drill to work. They should look like this when done. Drill the holes in the two thick pieces. The with of the holes should be a bit bigger than the diameter of the shaft. When drilling, go slowly to avoid splitting. Make sure you drill in the middle of the wood. When done you should have two big holes in the large pieces big enough for the shaft. For drilling hole likes these where the edge of the drill bit comes close to the vice we let an adult do the final set up and test.
After you have drilled all the holes apply bee’s wax. The bee’s wax makes them smooth and help avoid splitting.
To apply the bee’s wax use an old towel. Since bee’s wax does not go bad, we use the same rag repeated for other projects.
Drill two holes at the tip of the shaft the same width as the string you will be using. Measure the string and put the string through it.
Now drill holes at both ends of the handle. Make sure the hole is in the same direction as the shaft hole.
Next, assemble the pump drill by sliding the shaft through the handle.
Then loop the string through the two holes you drilled in the handle.
Adjust the string so that the center stick if a little less than halfway down the pole. Then tied knots on both ends of the string.
Now slide the spindle onto the shaft.
Use a thin board of wood like the one shown in the photo and break off a strip.
Wedge the strip of wood in the gap to make the fit tight. Add more strips of wood as needed. The spindle should not be able to move.
And finally, cut a slot at the end of the shaft by cutting two parallel cuts. Then use a chisel to clean up the notch. Secure a sharp stone shaped like an arrow tip with string.
Yay! You finished!
Now you know how to make a DIY pump drill!
You use the drill by first winding it up. Then gently push down on the handle. Let the string rewind itself (thanks to the spindle whorl). Do not push the stick up but let the pump drill wind back then, again, gently push down.
We laid out the final design before threading the wire through the holes we drilled.
